Crown Com-tech Ct-1610 Professional Stereo-dual Channel-power Amplifier-1920w #3

  

I have packaged amplifiers for nearly 20 years. It will be packaged very well with premium packaging materials. This is an opportunity to own a great looking and working Crown Com-Tech CT-1610 stereo, dual channel, power amplifiers. This piece looks great and shows very little signs of use. It is unique in it can be run in traditional modes such as 4 ohms stereo, 8 ohms stereo and bridged modes as well as 70v and 140v, providing up to 1920 watts of power.

It features a PIP-USP3 IQ DSP Programmable Input Processor. I have PIP-SMT IQ2 / PIP2 cards available in a separate listing if that is your preference. It powers on, passes clear audio, the selectors work, and the volume pots work and are not scratchy. It has spent its life in a pet free, smoke free, temperature controlled environment.

It went straight from the box to the rack and is thus, very nice. It will be a great piece for someone. You get exactly what you see pictured. It weighs a 57 lbs before packing.

The photo of the two racks show how these were set up for use. These were never run hard. You get the single amplifier featured in the photos for the price shown.

Please read the specs and more information from Crown below. Designed from the ground up exclusively for the professional sound contractor, Com-Tech® offers incredible features, flexibility, and the best long-term value in commercial audio today. The Com-Tech 10 Series amps offer the same features and performance of the original Com-Techs while delivering upgraded features to help make your job easier. In a profession where unplanned service calls quickly wipe out profits, the Com-Tech 10 Series is designed to be the most reliable amplifier you can install.

Safe with all types of loads. With 8/4-ohm output, all Com-Techs are rated for 4 to 8 ohms in Dual mode, 8 to 16 ohms in Bridge-Mono mode, and 2 to 4 ohms in Parallel-Mono mode.

With 70-volt output, rated loads vary among the different models for each dual/mono mode (see chart below for rated 70V). Unique power supply allows channels to be independently operated in either 70-V or 8/4 ohm mode. Remote feature allows amplifier to be turned on and off from a remote location by adding an optional R. Crown's Grounded BridgeT design delivers large voltage swings without using easily stressed output-transistor configurations like conventional amplifiers.

The results are lower distortion and superior reliability. Patented ODEP ® (Output Device Emulation Protection) circuitry compensates for over- heating and overload to keep the amplifier working when others would fail. IOC ® (Input/Output Comparator) circuitry immediately alerts of any distortion exceeding 0.05%, providing dynamic proof of distortion free performance.

Enhanced PIP2T (Programmable Input Processor) connector accepts new accessory modules that tailor the amplifier to suit specific applications. Full protection from shorted, open and mismatched loads; general overheating; DC; high-frequency overloads, and full protection from internal fault are provided by our latest protection scheme: Quad-Mute. PIP-USP3 is a DSP-based PIP module that integrates into a 100-Mb Ethernet network via TCP/IQ protocol. An extremely versatile speaker-processing unit that mounts right in your Crown amplifier, this compact module greatly reduces the costs of typical audio systems while eliminating the rack space needed for signal processing. Offers up to thirty-two filters per channel as well as load supervision that continuously monitors the load impedance using the signal source as the test signal. Also includes compressors, limiters, error reporting, ten internal presets, up to 2 seconds of delay per channel, and noise and sine-wave generators. Also includes line voltage monitoring when installed in Crown CTs series amplifiers.

Requires FREE IQwic Software and a computer for initial setup. 100Mb Ethernet single-plug solution for TCP/IQ control and monitoring. Listen Bus amplifier output monitor. 24 bit conversion with 32 bit, floating point DSP processing.

64 assignable filters with 9 different filter types including all-pass filters. Over 2 seconds of delay available per channel. Input compressors and output limiters for each channel.

Dual, uncorrelated noise generators for noise masking. Firmware upgrades via the network.

Reliable FLASH memory backup of all parameters. I used a high resolution camera to give you accurate pictures of its condition. I have years of experience packaging delicate electronics, so rest assured, this will be packaged very well. I also use high quality packaging materials. Also, please check out the other items in my store.

Thank you for looking and God bless!