QSC ISA1350 Professional Power Amplifier- Perfect Working Condition Amp

  

This is a QSC ISA1350 series professional 70v amp, stable down to 2 ohms. In perfect working condition with light cosmetic wear. Drives 70V lines directly with 1500 watts per channel. Rear panel gain controls for tamper resistance; 2-dB detents allow for quick and repeatable settings.

XLR and detachable Euro-style input connectors. DataPort V2 for use with DPV2-compatible signal processing accessories (XC-3, SF-3, LF-3) and DSP-3/DSP-4 (with external power supply).

Independent defeatable clip limiters for reduced distortion. Selectable high-pass filters (30 Hz or 70 Hz) protect speakers and prevent speaker transformer saturation, with minimal effect on program material. Three-tier Class H complementary bipolar output circuitry reduces AC power draw and waste heat by 50%. Front panel indicators include power, signal, clip and protect. Covered barrier strip output connectors for safety agency compliance.

Automatic on-demand variable-speed fan: quiet normal operation, with maximum cooling when needed. Rear-to-front air flow helps keep equipment racks cool. Stereo, bridge, or parallel operating modes. Comprehensive protection circuitry including DC, infrasonic, thermal overload, and short circuit protection.

OUTPUT POWER PER CHANNEL, STEREO MODE, both channels driven. 8, 20 Hz20 kHz 0.1% THD 4, 20 Hz20 kHz 0.1% THD 2 1 kHz 1% THD.

185 W 280 W 430 W. 260 W 425 W 700 W.

450 W 650 W 1200 W. 800 W 1300 W 2000 W.

DIRECT POWER PER CHANNEL, STEREO MODE. 70V, 20 Hz20 kHz +0/-0.3 dB 0.5% THD. TRANSFORMER-ISOLATED OUTPUT POWER PER CHANNEL, STEREO MODE. 70V or 100V, 50 Hz16 kHz 0.5% THD 25V, 50 Hz16 kHz 0.5% THD.

OUTPUT POWER, BRIDGED MONO MODE. 8, 1 kHz 0.1% THD 4 1 kHz 1% THD. TRANSFORMER-ISOLATED OUTPUT POWER, BRIDGED MONO MODE. 140V or 200V, 50 Hz-16 kHz 0.5% THD. Signal to Noise (20 Hz-20 kHz).

1.15 V (+3.4 dBu). 1.07 V (+2.8 dBu).

1.24 V (+4.1 dBu). 33.4× (30.5 dB). 64.0× (36.1 dB). 36 lb (16.3 kg).

47 lb (21.3 kg). 68 lb (30.8 kg).

44 lb (20.0 kg). 49 lb (22.3 kg). 42 lb (19.1 kg).

53 lb (24.0 kg). 77 lb (34.4 kg). 50 lb (22.7 kg). 63 lb (28.6 kg). Distortion (Typical) 20 Hz20 kHz: 10 dB below rated power 1.0 kHz and below: full rated power.

Less than 0.03% THD, 4 ohms and 8 ohms Less than 0.03% THD, 4 ohms and 8 ohms. Frequency Response 10 dB below rated output power. ISA 280, 450, 750 and 1350.

20 Hz20 kHz, +0/-1 dB; -3 dB points: 5 Hz and 50 kHz. ISA 300Ti, 500Ti and 800Ti.

Damping Factor with 8 Load (direct outputs). Greater than 200; ISA 1350 greater than 250. Less than 1.5 dB. 10 k unbalanced, 20 k balanced. 10 V rms (+22 dBu). Continuously variable speed fan, back-to-front air flow. Input: Active balanced; 3-pin Euro-style detachable terminal block and XLR (pin 2+) Output: Covered barrier strips. Front: AC switch Rear: Ch. 2 gain knobs, 10-position DIP switch.

PWR-ON: Green LED; SIGNAL: Green LED (1 per channel); CLIP: Red LED (1 per channel). 5.25 x 19 x 15.9 / 3RU. 133 x 483 x 400 / 3RU. Full short circuit, open circuit, thermal, ultrasonic, and RF protection; Stable into reactive or mismatched loads.

120 or 230 VAC, 5060 Hz. On/off muting; Triac crowbar: ISA 750, 1350, and 800Ti; AC coupling: ISA 280, 300Ti, 450, and 500Ti. All specifications are subject to change without notice. The item "QSC ISA1350 Professional Power Amplifier- Perfect Working Condition Amp" is in sale since Sunday, November 17, 2019. This item is in the category "Musical Instruments & Gear\Pro Audio Equipment\Amplifiers".

The seller is "megmarsh2012" and is located in Austin, Texas. This item can be shipped to United States.

1. Brand: QSC
2. Number of Channels: 2
3. Model: ISA1350
4. RMS Power: 4000 W
5. Type: Power Amplifier
6. Form Factor: Rack Mountable
7. Features: Crossover