Crown Pro XTI4002 XTI 4002 3200w Professional Power Amplifier Amp, Advanced DSP

Crown XTI4002 XTI-4002 2 Channel 2400 Watt Power Amplifier with Peak Plus Limiters Providing the Ultimate in System Performance and Protection By Allowing Full Control Over Threshold, Attack, and Release. Condition: AN OPEN BOX ITEM.

6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed. Crossover Filters Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control. Output EQ 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Delay For signal alignment of driver; 50 mS of total delay. SubHarmonic Synth Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.

PeakxT Plus Limiter User defeatable limiter that allows users to control Threshold, Attack, and Release times. Presets 50 total presets, 49 of which are user-definable. XTI4002 2 Channe Power Amplifier. Peak Plus Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release. Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning.

3 User-defined fan mode controls - normal, early and fullspeed - for matching fan performance to a specific application. New system monitoring provides software visibility of AC line voltage and power supply temperature.

Locking power cord clip provides a secure connection between the amplifier and power cord. Updated HiQnet Band Manager and System Architect control software. Increased number of presets to a total of 30; 29 of which are user definable. Sensitivity (for full rated power at 4 ohms): 1.4 Vrms.

Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, -1 dB. Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted). Damping Factor 20 Hz to 1 kHz: > 500.

Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db. Maximum Input Signal: +22 dBu typical.

AC Line Voltage and Frequency Configurations: 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz. AC Line Current(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 10.5A; no more than 38W at idle.

Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing). Level: Two front-panel rotary level controls, one for each channel. Power Switch: On/Off switch applies AC power to the amplifier. Sel/Prev/Next Buttons: Three buttons near the LCD screen that are used to access menu items and front panel lockout. LCD Screen: Backlit liquid crystal display that shows preset and processing status. Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).

10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip. 20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip. Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio. Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion.

Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions. Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power.

Input Connectors: XLR, one per channel. Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.

Output Connectors: Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 2 outputs for use with optional single 4-conductor cable.

Two binding post outputs (in parallel with Speakon® connectors). HiQnetT USB Connector: Type B, connects to HiQnetT network.

Cooling: Proportional speed fan with front-to-rear airflow. Dimensions (WxHxD): 19" x 3.5" x 12.25. Net Weight: 18.5 lbs (8.4 kg). For the Owner's Manual.

If your item is defective or you want to return it for any reason within the first 30 days of when it was delivered to you; you have the following options. We will send you a. To replace the item for a brand new one.

All replacements and exchanges are free. This includes blown speakers with burned voice coils.

The item "Crown Pro XTI4002 XTI 4002 3200w Professional Power Amplifier Amp, Advanced DSP" is in sale since Tuesday, May 22, 2018. This item is in the category "Consumer Electronics\TV, Video & Home Audio\Home Audio\Receivers & Amplifiers\Amplifiers & Preamps". The seller is "audiosavings" and is located in Inwood, New York.

This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, South Korea, Indonesia, Taiwan, South africa, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Pakistan, Paraguay, Reunion, Uruguay.

UPC: 871015005393
Form Factor: Rack Mountable
Country/Region of Manufacture: China
Brand: Crown
Model: XTi 2 Series 4002
Features: Limiter
Custom Bundle: No
Rack Mountable: No
Audio Outputs: speakON
Audio Inputs: XLR
Type: Power Amplifier
Modified Item: No
RMS Power: 1600 W
Number of Channels: 2
MPN: XTI4002