Bose PowerMatch PM8500 Configurable Professional Power Amplifier. This is a Bose PowerMatch PM8500 Configurable Professional Power Amplifier. 1 8 Position Power Output Connector.
8 3 Pin Input Connectors. 3-pin Phoenix Contact® (green color; part # 1776168).
1 3 Pin Fault Connector. DVD with all documentation and files available from the Bose Web Site (Install and Operation Manual included). This is my item 900 901. 2 were available at listing time.
Where I have a lot of other scientific equipment and accessories for sale. This came out of a local Natick Restaurant. More Information: Power On Screen Bose PM8500 Boot: IPL-7670 v0.10 Firmware v1.153 build 23 Speaker EQs: v0.016 DSP: 1.14.4 build 1. Minimum Frequency Response: 20 Hz. Maximum Frequency Response: 20 kHz.RMS Output Power: 4000 W. Weight (Approximate): 28.40 lb. The Bose PowerMatch PM8500N configurable professional power amplifier provides concert-quality sound with a high level of scalability and configurability. The PM8500N offers multiple channel and power options, an integrated audio DSP, front panel interface, USB connection, and Ethernet-based network configuration, control and monitoring. An expansion slot supports inputs from optional digital accessory cards. PowerMatch amplifiers utilize numerous Bose technologies to deliver an unprecedented combination of performance, efficiency, and ease of installationall in a reliable, proprietary design. The PM8500N USB connection provides single-unit setup and control using Bose ControlSpace Designer software. Ethernet connectivity is also provided for configuration, network control, and monitoring of multiple amplifiers. Allows each 4-channel loudspeaker block to be configured as Mono, V-Bridge, I-Share or Quad modes, allowing the total available power of the amplifier block to be allocated to one or more output channels. The amplifier is capable of driving both low impedance and 70/100V loudspeaker loads directly.
PowerMatch amplifiers can be fully configured using ControlSpace Designer software via the onboard front panel USB connection, or the rear panel Ethernet connection. Using ControlSpace Designer software you can access additional features including: Parametric EQ stages, load sweep of each output channel and auto standby. ControlSpace Designer software is also used to integrate network model PowerMatch amplifiers into larger control and monitoring systems comprised of Bose ESP processors and CC control centers. When enabled, this function automatically enters/exits Standby Mode, allowing the system to consume less power. Dual voltage and current feedback loop.Proprietary design combines Class-D efficiency with a unique current and voltage feedback loop circuit that continuously monitors and controls both the current and voltage delivered to the loudspeaker load. Independent of power level and load impedance, the amplifier consistently delivers the widest possible dynamic range, frequency response and lowest possible distortion. Regenerative 4-quadrant power supply enables higher power density while allowing the re-use of energy from reactive loads that is normally wasted in conventional Class-D designs. This highly efficient amplifier design delivers sustainable and repeatable low frequency response. Fast-tracking power factor correction (PFC). Efficiently manages the current drawn from the AC mains, allowing the amplifier to drive loudspeakers to maximum output longer without power fluctuation. PFC provides superior transient response and functions at peak burst power much longer than conventional Class-D amplifier designs to satisfy the requirements of even the most demanding program material. 4000 W (500 W x 8 channels at 4 ohms). 71 / 142 V (Mono / V-Bridge, I-Share, and Quad modes). 36 / 42 / 36 / 42 dB (Mono / V-Bridge / I-Share / Quad modes). 20 Hz - 20 kHz (at 1 W and +/- 0.5 dB). > 102 dB (1 dB below rated power, A-weighted). > 65 dB (adjacent channels, at 1 kHz).
> 1000 (10-1000 Hz, 4 ohms, at amplifier output). Total Latency (Analog In - Amp Out). Input to Output Signal Routing. 5-band PEQ (+/- 20 dB), notch, shelving, high pass, low pass. Butterworth, Bessel, or Linkwitz-Riley, up to 48 dB/octave.
9-band PEQ (+/- 20 dB), shelving, high pass, low pass, 2-band RoomMatch array EQ. 0, +4, +12, +24 dBu, selectable. Digital: 0, -12, -20, -24 dBFS, selectable. +24 dBu (at 24 dBu sensitivity setting).
8-pin Phoenix Contact connectors (part # 1778120), supports 10-24 AWG wire. Mute, input sensitivity, output configuration, output attenuation, EQ on/off, preset select. Additional controls available w/ ControlSpace Designer software. 20A (120 V) or 16A (230 V). 80 V (reduced output power).
15.4 A (230 VAC, 50 Hz). > 75 % (pink noise input signal).
High temperature, DC, HF, short, voltage limiter, current limiter, inrush current, mains circuit breaker protection. Dimensions (H x W x D).
88 mm × 483 mm × 525 mm (3.5 × 19 × 20.7) - 2 rack space. 0 °C - 40 °C (32 °F - 104 °F). Microprocessor-controlled, variable-speed fans, front to rear airflow. ControlSpace Designer software V3.2 or greater.
USB (type B), Ethernet (RJ-45, 100Mb). NC/NO Relay Contact (1 A, 30 VDC), 3-pin Phoenix Contact connector (orange color; part # 1976010). Please don't open a case. Cases count against me even if they are resolved.I stand behind my items and will work out any problems that you may have with an item. We do not mark merchandise values below value or mark items as "gifts". US and International government regulations prohibit such behavior.
Powered by SixBit's eCommerce Solution. The item "Bose PowerMatch PM8500 Configurable Professional Power Amplifier" is in sale since Tuesday, June 29, 2021. This item is in the category "Musical Instruments & Gear\Pro Audio Equipment\Amplifiers".
The seller is "massetrecovery" and is located in Natick, Massachusetts. This item can be shipped to United States.